樓承板是將樓板中的鋼筋在工廠加工成鋼筋桁架，并將鋼筋桁架與鍍鋅鋼板焊成一體的組合模板，具有施工速度快、高強度等特點，下面濟南樓承板廠家淺談樓承板在施工時存在的問題！

Floor bearing plate is a composite formwork that processes the steel bars in the floor slab into steel bar trusses in the factory and welds the steel bar trusses and galvanized steel plates into a whole. It has the characteristics of fast construction speed, high strength, etc. Next, Jinan floor bearing plate manufacturer will talk about the problems in the construction of floor bearing plates!

1.定制的樓承板底模不平整，鋼筋桁架變形，影響鋼筋桁架整體受力。所以在選擇的樓承板生產廠家的時候一定要選擇正規的生產廠家。

1. The bottom formwork of the customized floor support plate is uneven, and the steel bar truss is deformed, which affects the overall stress of the steel bar truss. Therefore, when choosing the manufacturer of floor bearing plate, we must choose a regular manufacturer.

2.樓承板在鋪設時，沒有事先放樣板確定基準線，樓承板端部支座豎筋、鍍鋅底模沒有與鋼梁上翼緣進行焊接牢固。導致在鋼梁的上翼緣搭接長度不足，存在漏漿的現象。

2. During the laying of the floor bearing plate, the template was not set out in advance to determine the baseline, and the vertical reinforcement of the support at the end of the floor bearing plate and the galvanized bottom formwork were not welded firmly with the upper flange of the steel beam. As a result, the lapping length of the upper flange of the steel beam is insufficient and there is grout leakage.

3.鋼筋桁架在鋼梁斷開處沒有設置連接鋼筋、附加鋼筋及分布鋼筋，遇到孔洞及經過切割的異形處，沒有加焊附加鋼筋，板邊有漏漿部位的存在。

3. No connecting reinforcement, additional reinforcement and distribution reinforcement are set at the steel beam disconnection of the reinforcement truss, and no additional reinforcement is welded at the holes and cut abnormities, and there is mortar leakage at the edge of the plate.

4.圓柱頭栓釘與鋼梁上翼緣焊縫不合格且間距布置不到位，影響樓板整體的抗堿性。

4. The welding seam between the cylinder head stud and the upper flange of the steel beam is unqualified and the spacing is not in place, which affects the alkali resistance of the whole floor.

5.預埋管線及電氣接線盒時，切斷鋼筋桁架，導致在樓承板底模開孔處造成漏漿。

5. When embedding pipelines and electrical junction boxes, cut off the steel bar truss, resulting in mortar leakage at the opening of the bottom formwork of the floor support plate.

6.邊模板焊接不牢固不順直，影響混凝土澆筑的質量。有懸挑板時，沒有設置加固角鋼或槽鋼，沒有設置臨時支撐。

6. The welding of side formwork is not firm and straight, which affects the quality of concrete pouring. When there is a cantilever plate, there is no reinforcement angle steel or channel steel and no temporary support.

以上就是小編整理的樓承板在施工時可能會出現的幾點問題，希望對大家有所幫助。

The above are some problems that may occur during the construction of the floor bearing plate, which I hope will be helpful to you.

施工時，樓承板可隨施工荷載，直接鋪設到梁上，然后再進行簡單的鋼筋工程便可澆筑混凝土。由于減少了模板架設和拆卸工程，因而大大提高了工程的施工效率。但是樓承板在施工時如果不注意就會存在一些問題，以上所講解內容希望能夠給您幫助，關注我們http://m.jywhzx.com了解更多！

During construction, the floor bearing plate can be directly laid on the beam with the construction load, and then the concrete can be poured after simple reinforcement works. The construction efficiency of the project is greatly improved due to the reduction of formwork erection and removal works. However, if you don't pay attention to the construction of the floor bearing plate, there will be some problems. I hope the above explanation can help you and pay attention to us http://m.jywhzx.com Learn more!